A field comes out blank or wrong for one of three reasons: it isn't mapped, its source column is empty for some products, or a rule overwrote it. Check the Mapping tab first, then use Trace a product to see where the value came from.
A Field Is Empty or Wrong in My Feed
A field comes out blank or wrong because it isn't mapped, its source column is empty for some products, or a rule overwrote it. Find the cause on the Mapping tab and with Trace a product, then fix it.
Updated November 6, 2026
Start on the Mapping tab: is the field mapped?#
Open the catalog from your project's Catalogs list, choose the Mapping tab, and find the field in the Catalog fields table.
A field with no source is empty for every product, and you get no error. A required field left unmapped is counted in the chip at the top of the table ("2 required missing"). To fix it, map a feed column onto its row. See Mapping your feed to catalog fields.
Read the Fill column: empty for everyone, or just some?#
Once a field is mapped, the Fill column shows the percentage of products in your last import that got a value.
- A low or zero Fill means almost no product gets a value. The field is probably mapped to the wrong column, or to a column that's empty across your feed.
- A partial Fill, say 60%, means the source column is blank for the rest. Those products need a fallback (below). A required field with partial coverage also shows a warning tone and a note on its row ("120 empty").
If the number is dimmed with an asterisk, you've changed the field's mapping since the last import, so it still describes the old mapping.
Trace a product to see where the value came from#
When a field is wrong rather than empty, or the Mapping tab doesn't make the cause obvious, Trace a product shows where the value came from. Open it with the Trace button on the toolbar of the Rules tab or the Mapping tab.
Pick the product whose field looks wrong. Trace walks it through your rules as step-cards, each marked "applied" or "didn't apply", and ends in a "Catalog output" table with the final value of every field. Read the field you're chasing:
- If it carries a note such as "set by Clean up titles", that rule wrote the value. The rule is your suspect.
- If it shows a plain value with no note, the value came straight from your mapping. The source column is your suspect.
The full walkthrough is in Imports, warnings, and tracing a value.
Fixing the field#
Make your fix, then check it with Trace, which runs against your draft, so you can confirm it before you publish. Then choose Publish & import. Fill catches up after that import.
An empty field#
A blank cell, an empty tag and a missing column all count as empty, so one fallback covers them.
- Empty for every product: map the field to the right column on the Mapping tab.
- Empty for some products: stack a fallback, which is a second column, a fixed value or a value looked up from another feed, used when the first source is empty. See Mapping your feed to catalog fields and Joining another feed with a lookup.
To guarantee a value for a whole group of products, a rule can set a fixed default when a condition matches. See Fixing your feed data with rules.
A wrong value#
- A rule overwrote it. Open that rule on the Rules tab. Rules run top to bottom and each sees the result of the ones above it, so if two rules write the same field, the last one wins. Change the rule's conditions so it stops catching this product, or change the value it sets.
- The source column is wrong. Remap the field if it points at the wrong column. If the raw value needs cleaning, use "+ Add step" to trim, replace, re-case or reformat it. See Steps: changing a value before it is used.
- The column holds several values and only the first is used. A field that takes one value (Title, Price, Image link) gets the first of them. Add a Last or Nth step on the mapping to pick another, or a Join step to write them all into one text. If the first value is sometimes blank, add a Filter step first. The catalog's Activity tab warns you where this happens. See When Renable warns that only the first value is used.
FAQ#
The field is filled in Renable but still missing or wrong in my ads. Why?
If you've published and imported, the ad network may not have read your feed yet: it does that on its own schedule. The value itself may also be one it doesn't accept. A barcode (GTIN, EAN or UPC) whose check digit doesn't match, or a Google category that isn't in Google's taxonomy, is sent as your feed gives it, and the import warns you about it. Fix it at the source or with a rule. See Imports, warnings, and tracing a value.
Or ask Aimée#
Ask Aimée something like "why is the brand empty on this product?". She can tell you which column, fallback or rule decided the value, fix it, and publish once you approve.